Riello Heavy Oil Burners

Product Details:

From our extensive range of products, our clients can avail a quality assured collection of Riello Heavy Oil Burners.

Additional Information:

• Item Code: HOB-01

Product Details:

The RN series of burners covers have been designed for use in hot or superheater water boilers, hot air or steam generators, diathermic oil boilers. the burners are fitted with an electronic device led panel, which supplies Information about burner working. All necessary components of the hydraulic heavy-oil circuit are assembled in a separate structure, called BAG, for easy and fast installation. forward Optimisation of sound emissions is guaranteed by the use of fan forwarding curved blades and sound deadening material incorporated in the air suction circuit. The elevated performance of the fans and combustion head, guarantee flexibility of use and excellent working. The exclusive design ensures reduced dimensions, simple use and maintenance. A wide range of accessories guarantees elevated working flexibility

Monobloc forced draught heavy on the l burner, two stage operation, made up of:

• Air suction circuit lined with sound-proofing material
• Fan with reverse curve blades
• Air damper for air setting controlled by a servomotor
• Combustion head, that can be set on the basis of required output
• Photocell for flame detection
• Burner safety control box
• Electronic device to check all burners operational modes (Led Panel)
• Burner on/off switch
• Manual 1st and 2nd stage switch
• Plugs for electrical connections (RN 28-38-50)
• Flame inspection window
• Slide bars for easier installation and maintenance
• Protection filter against radio interference

Bag:

• Pressure gauge for fuel supply loop
• Atomising pressure gauge
• Self-controlling resistances for warming suction filter, delivery filter, valve and pump
• High and Low point thermostat
• High point thermostat with reset push-button
• Loop pressure control switch with burner operation enable (set at 1 bar)
• Pump
• Pump motor
• Pre-purge valve
• Degassing unit
• Valve for gas release from degassing unit
• Comb-filter at delivery
• Terminal strip
• Wiring Looms
• Bag/Burner electrical connection socket
• Electronic thermostat
• Heating element Pt100
• Back pressure valve
• Comb-filter at pump suction
• Pre-heater

Standard Equipment:

• 2 flexible hoses for burner/bag connection (L = 1.3 m)
• 1 insulation for flexible hoses
• 2 nipples for flexible hoses
• 1 insulating screen
• 4 screws for fixing the burner flange to the boiler
• Wiring looms for electrical connections (for RN 28-38-50 model)
• 1 tube for installing BAG on left (for RN 28-38-50 model)
• 2 nozzles
• Instruction handbook for installation, use and maintenance
• Spare parts catalogue

Product Details:

Heavy oil burner series P/NA is an evolution of the traditional heavy oil modulating burners P/N series. The new range applies a different technology to replace the usual mechanical atomizing (high pressure) by “assisted” air/steam atomizing (feed pressure 5-8 bar) and taking the related advantages when burning heavy fuels (even vegetable oil). The upgraded design has been introduced to meet even the worst fuel qualities and to reach anyway the best achievable combustion performance (lower particulate and NOx emissions). The capacity range is suited to cover applications on steam generators designed for production from 1 to 6 tons/hr of steam or an equivalent capacity in case of another kind of boiler. Reliable and smooth ignition is achieved by LPG pilot burner installed into the combustion head. The control system includes all safety and operation interlocks, making possible the configuration compliance to the latest design norms on world-wide base (i.e. EN 267 – UL 296 – others), by the available options on request.

Additional Information:

• Item Code: P140P-NA-ECO

Product Details:

Being a customer oriented organization, we are highly engaged in providing a wide range of Modulating Heavy Oil Burner.  high-efficiency, industrial-grade combustion systems designed for wide-ranging, continuous, and variable load applications. Covering capacities from 400 to 5340 kW, they feature a PID logic controller, 3:1 turndown ratio, and specialized heating for heavy oil. These burners, popular in India for industrial use, offer superior reliability with robust, easy-to-maintain designs, including sliding bars for access to components. 

Product Details:

Press N/Eco burner series covers a fi ring range from 171 to 1140 kW and it has been designed for operation with low sulphur fuels. The burners are equipped with a separate low speed pump. They have been designed for use in civil installations of average dimensions, like building areas and large apartment groups or for use in industrial applications, like small or medium plants. Operation is two stage; a servomotor adjust automatically air damper opening, to obtain the right air delivery on both stage. The burners are fi tted with a microprocessor control panel which supplies indication of operation and diagnosis of fault cause. The combustion head, that can be set on the basis of required output, allows optimal performance ensuring good combustion and reducing fuel consumption and is available in two different length to be selected on the basis of specifi c application requirements. In basic version the burners are supplied for use with heavy oil 7°E viscosity, but they can be supplied with higher viscosity oil with a specifi c heaters kit. Simplifi ed maintenance is achieved by the slide bar system, which allows easy access to all of the essential components of the combustion head.

Monoblock forced draught heavy oil burner, two stage operation, made up of:

• Air suction circuit
• Fan with forward curved blades
• Air dampers for air setting controlled by a servomotor
• Combustion head, fi tted with:
• stainless steel end cone, resistant to corrosion and high temperatures
• Ignition electrodes
• Fl ame stability disk
• Gears pump for high pressure fuel supply, fi tted with:
• Fi lter
• Pressure regulator
• Connections for installing a pressure gauge and vacuometer
• Internal by-pass for single pipe installation
• Valve unit with a double oil safety valve on the output circuit
• Double fi lter between pump and nozzle
• Oil preheater provided with chance of a thermometer application for temperature control
• Installed electrical heaters on pump, nozzle holder, valves assembly
• Servomotor for air damper regulation
• Air pressure switch
• Photocell for fl ame detection
• Microprocessor-based fl ame control panel, with diagnostic function
• Flame inspection window
• Slide bars for easier installation and maintenance
• Protection fi lter against radio interference

Standard equipment:

• 2 fl exible hoses for pipe connection
• 2 gaskets for fl exible hoses
• 2 nipples for fl exible hoses
• 1 thermal insulation screen
• 4 screws for fi xing the burner fl ange to the boiler
• 2 nozzles (see table of available burner model)
• 2 extensions for bars (for long head version)
• Instruction handbook for installation, use and maintenance
• Spare parts catalogue.

Product Details:

Being a customer oriented organization, we are highly engaged in providing a wide range of Three Stage Heavy Oil Burners.

Additional Information:

• Item Code: HOB-02

Product Details:

Being a customer oriented organization, we are highly engaged in providing a wide range of Industrial Heavy Oil Burners.

Additional Information:

• Item Code: HOB-03

Product Details:

The PRESS N series of burners covers a firing range from 85 to 1140 kW and they have been designed for use in civil installations of average dimensions, like building areas and large apartment groups or for use in industrial applications, like small or medium plants. Operation is two stage; a servomotor adjust automatically air damper opening, to obtain the right air delivery on both stage. The combustion head, that can be set on the basis of required output, allows optimal performance ensuring good combustion and reducing fuel consumption and is available in two different length to be selected on the basis of specific application requirements. In basic version the burners are supplied for use with heavy oil 7°E viscosity, but they can be supplied with higher viscosity oil with a specific heaters kit. Simplified maintenance is achieved by the slide bar system, which allows easy access to all of the essential components of the combustion head.

Additional Information:

• Item Code: PRESS30N

Product Details:

Specifications

• Combustion air temperature may range from room temperature to 100 DegreeC.
• Output Min 10 kW
• Output Max 250 kW
• Flame Diameter 120 mm
• Flame Length 600 mm
• Gas Supply Pressure 30 mbar
• Air Supply Pressure 65 mbar
• Weight (Combustion chamber included) 30 kg

 

Note

• Above price is only for burner not included the price for any accessories. Terms & Condition is apply
  
  

 

Product Details:

The PRESS P/N series of burners covers a firing range from 400 to 5130 kW. They have been designed in three versions for use in commercial and industrial installation, to burn different oil viscosity from 7 up to 60°E @ 50°C. Operation can be “two stage progressive” or, alternatively, “modulating” with the installation of a PID logic regulator and respective probes, which guarantees a turn down ratio of 3:1. The versatility of this range makes the burner well suited for use on steam boilers where the load factor is subject to wide variations, on thermal oil boilers and on boilers for particular heating plants, as hospitals or similar. Simplified maintenance is achieved by the Riello designed slide bar system, which allows easy access to all of the essential components of the combustion head.

Additional Information:

• Item Code: HOB-04